Tc Serie Gürtel und Getriebe Kombi Mischpult
Basisinformation
Modell: TC series
Produktbeschreibung
Modell Nr .: TC-Serie Arbeit: Hochgeschwindigkeits-Mischer Zusätzliche Fähigkeiten: Trocknungs-Getriebe-Verhältnis: 4.17-7.5 Ausgangsdrehmoment: 45-850nm Farbe: Blau, Grau Anwendungsbereich: Bergbau-Installation Vorgehensweise: Pls Siehe Installationsanleitung Spezifikation: CE, ISO9001: 2008, TUV, SGS, etc HS-Code: 8483409000 Mischer-Typ: Pulvermischer Anwendung: Flüssigkeit mit suspendierten Feststoffen, Pulver, viskose Flüssigkeit, Flüssigkeit, Granulat Leistung: 0,55-22kw Ausgangsgeschwindigkeit: 140-360rpm Gehäuse Material: Hard-Face Hauptkunde : Südamerika-Schmierung: Öl-Sumpf-Schmierung Warenzeichen: HFT berühmte Marke Ursprung: Wenzhou, Zhejiang, China TC-Serie Gürtel und Getriebe Kombination Mischer:
Leistung: 0 & Periode; 55-22K
Verhältnis: 4 & Periode 17-7 & Periode; 5
Ausgabegeschwindigkeit: 140-360RPM
Drehmoment: 45-850Nm
Über HFT:
Firmenname: Zhejiang Hengfengtai Reducer MFG & Zeitraum; CO & Periode ;, Ltd
Gründungsjahr: 1991
Anzahl der Mitarbeiter: 500 Mitarbeiter
Fabrik Platz: 50000 Quadratmeter
Wichtigste Produkte: Mit Getriebe reduzieren Serie Produkte als führende, erweitern, um elektrolytische Aluminium-Ausrüstungen, Mischanlagen, Präzisions-Getriebe Ausrüstungen, Umweltschutz Ausrüstungen und so weiter große Maschinen Anlagen und Zeitraum;
Qualifikationen von quatity: CE, ISO9001, TUV, SGS, etc & Zeitraum;
Leistung: 0 & Periode; 55-22K
Verhältnis: 4 & Periode 17-7 & Periode; 5
Ausgabegeschwindigkeit: 140-360RPM
Drehmoment: 45-850Nm
Über HFT:
Firmenname: Zhejiang Hengfengtai Reducer MFG & Zeitraum; CO & Periode ;, Ltd
Gründungsjahr: 1991
Anzahl der Mitarbeiter: 500 Mitarbeiter
Fabrik Platz: 50000 Quadratmeter
Wichtigste Produkte: Mit Getriebe reduzieren Serie Produkte als führende, erweitern, um elektrolytische Aluminium-Ausrüstungen, Mischanlagen, Präzisions-Getriebe Ausrüstungen, Umweltschutz Ausrüstungen und so weiter große Maschinen Anlagen und Zeitraum;
Qualifikationen von quatity: CE, ISO9001, TUV, SGS, etc & Zeitraum;
Breakdown content | Possible reasons | Removing methods |
No load condition, Motor not work |
Black out | Check power supply,ask electric power co., |
Connecting line break | Check wiring | |
Switch contact undesirable | Fix and change | |
Wire coil break | Sendprofessional motor factory repair |
|
Three-phase motor connect single phase voltage | Make sure voltage andmode of connection | |
Single-phase motor no connect capacitor | Connect a capacitor | |
Single-phase motor starter bad action | Sendprofessional motor factory repair |
|
Gear, axis and the bearing damage | Sendprofessional motor factory repair |
|
When load, Motor works |
Voltage below level | Check power line whether is too long or carefully |
Gears, weared | Sendprofessional motor factory repair |
|
Overload operate | Reduce load | |
Overload operate | Reduce load | |
Abnormal heating | Start, stop excessive | Reduce the frequency of use |
Bearingweared | Fix and change bearing | |
Deterioration of grease | Change oil | |
Voltage too high or too low | Make sure voltage whether is normal | |
Big noise | Loud and continuous: bearing damage, gear broken | Change bearing or gear |
Occasional loud: Gear injury, unusual thing got stuck | Pick up the unusual thing, and change gear | |
Abnormal unstable operating noise: Oil has been contaminated or insufficient oil | Check the oil color, concentration, oil level | |
Vibration is too large | Gears, bearing weared | Change the gear or bearing |
Fixed bad, loose bolts | Refasten it | |
Bottom of the fixed mounting rigidity bad | Increased rigidity of bottom | |
Oil leak:In the motor flange;In the motor oil seal;In the reducer flange;In the output part of the oil seal |
Loose bolts | Refasten it |
Ring damage | Change the seals | |
Leakage from air plug | Too much oil | Adjust the oil quantity |
Vent plug on incorrect | Assemble the air plug with right way | |
Frequent cold starts (oil foaming) or the oil level is too high | Change vent into the exhaust valve | |
Output sahft no work when motor works | Reducer shaft key connection damage | Send reducer factory repair |
Produktgruppe : Rührwerk / Mischgerät
Premium Related Products
andere Produkte
heiße Produkte
Fenner Hsmr Shaft Mounted Reducer E-50-a 20/1 Ausgangsbohrung 55mmJw Serie Schraubbolzen für Jwm250DOFINE DXG Serie Wellengetriebe für KonverterMB Serie stufenloser GeschwindigkeitsreduziererDOFINE WB Zykloidal Micro GetriebemotorX-Serie Zykloide-Pin-Rad-VariatorRV Serie Wurm GarboxG-Serie GetriebemotorT-KegelradgetriebeMotorischer StellantriebFA Serie Hohlwelle ParallelgetriebeDOFINE Motorreduzierung Getriebe GetriebeK47 GESCHWINDIGKEITSREDUZIERERDP-PlanetengetriebemotorS Serie Wurm mit 3-Phasen-MotorB Serie Kegelschraube Industrie Getriebe Motor